Sound System Overview

…::: Greater Works Ministries Sound System Overview :::…

Multiple Microphones feed into a single sound system
|
Tascam M-216 Mixer
+
DBX 266 XL Dual Compressor
+
Behringer Ultra-Graph Pro GEQ3102 Ultra-Musical 31-Band Stereo Graphic Equalizer
+
Peavey M-2600 Power Amplifier
…::: Click to enlarge pictures :::…
.: The Tascam M-216 Mixer :.

Tascam M-216 Mixer
(top view)

Tascam M-216 Mixer
(back-left)

Tascam M-216 Mixer
(back-full)

Tascam M-216 Mixer
(back-right)
Stacked under the Mixer is…
DBX 266 XL Dual Compressor
+
Behringer Ultra-Graph Pro GEQ3102 Ultra-Musical 31-Band Stereo Graphic Equalizer
+
Peavey M-2600 Power Amplifier

DBX 266 XL Dual Compressor  /  Behringer Ultra-Graph Pro GEQ3102 Equalizer  /  Peavey M-2600 Amp
(front view)

DBX 266 XL Dual Compressor /
Ultra-Graph Pro GEQ3102 Equalizer
(back-left)

DBX 266 XL Dual Compressor /
Ultra-Graph Pro GEQ3102 Equalizer
(back-right)
Two output lines run from the Tascam M-216 Mixer to the Ultra-Graph Pro GEQ3102 Equalizer
(see image above for back-right)

Connection from Mixer to Equalizer Channel 1
Out from the Mixer is a 1/4″ male chord plugged in to the PGM OUT 1 port
(see upper image for: Tascam M-216 Mixer (back-left), (PGM OUT 1 is the 4th from left in image)
This chord converts to XLR male and goes in to the Equalizer as a 3-pin XLR connector into Input Channel 1
(see above image for: Ultra-Graph Pro GEQ3102 Equalizer (back-right), Input Channel 2 appears in the right side of image)
Connection from Mixer to Equalizer Channel 2
Out from the Mixer is a 1/4″ male chord plugged in to the OUTPUT-FLB port
(see above image for: Tascam M-216 Mixer (back-left), see chord with yellow sleeve)
This chord goes in to the Equalizer as a 1/4″ male in Input Channel 2
(see above image for: Ultra-Graph Pro GEQ3102 Equalizer (back-right), Input Channel 2 appears in the right side of image, see chord with yellow sleeve)
Two output lines run from the Ultra-Graph Pro GEQ3102 to a chord bundle

Connection from Equalizer to Amplifier Channel 1
A 1/4″ jack is plugged in the Channel 1 OUTPUT port and goes into the chord bundle

Connection from Equalizer Amplifier
A 1/4″ jack is plugged in the Channel 2 OUTPUT port and goes into the chord bundle

One output line runs from the Tascam M-216 Mixer to the Peavey M-2600 Amp

Out from the Mixer is a 3-pin XLR male connector plugged in to the PGM OUT 2 port
(see upper image for: Tascam M-216 Mixer (back-left), (PGM OUT 2 is the 3rd from left in image)
This chord goes in to the Amplifier as a 1/4″ male into Ch.A Input
(see image below for: Peavey M-2600 Amp (back))


Ultra-Graph Pro GEQ3102 Equalizer /
Peavey M-2600 Amp
(back)
.: Speakers :.

Speaker Front House Left High

data

Speaker Front House Right High

data

Speaker Front House Left Low

data

Speaker Front House Left Low

data

Speaker Back House Left

data

Speaker Back House Right

data

AUDIO RECORDING NOTES:
To Make a Line Recording from the Soundboard to a Laptop Using the Audacity Program.

  • On the TASCAM Soundboard Mixer – see back for RCA female outputs under notation of “EFF RTM” / “PGM OUT” and plug in right and left RCA male connectors (with a wire that outputs to a 3.5mm (1/8″) stereo male) into port “1” or “2.”
  • Plug the 3.5mm male connector from the wire above into the the microphone input on the laptop.
  • (On a Windows computer) go into “Recording devices” settings and Enable “Stereo Mix.”
  • Open the Audacity program and adjust settings for: “MME” and “Micrphone Hi Definition.”
  • Record.
Share